This post in the next paragraphs involving A Step-by-Step Guide to Installing a Bathtub is indeed attention-grabbing. Read it for your own benefit and decide what you think of it.
Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also often, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard job. If the old bathtub is readily obtainable, the project can relocate quickly; if you need to open a wall surface to remove the old tub and also position the brand-new bathtub, the job is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you may require a specialist plumber to make tube connections.
This short article will certainly aid you install a new bathtub in your restroom if you have already bought a new bathtub and also don't need to alter the setup of your previous water pipes.
Your tools and also product list should comprise the following:
- New Tub
- Hammer
- Pipeline Wrenches
- Prybar
- Shatterproof glass
- Degree
- Pliers
- Adjustable Wrench
- Putty Knife
- Screwdriver
- Cold Blade
- Measuring tape
- Pipeline Caps
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you must do is separate the water. After doing so, turn on the taps to drain any water remaining in the system. The process of eliminating the existing taps can be rather problematic due to the restricted access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been removed, use the same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Prior to going on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the maker provided backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The previous type should be attached to the tap finishes initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Tub
Using both wooden boards under its feet, put the bathtub in the needed position. The wood boards are helpful in equally spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the bath tub until the level checks out degree.
To set up faucets, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water system and also check all joints as well as brand-new pipework for leaks and tighten them if needed. Load the bath tub and also check the overflow outlet as well as the regular electrical outlet for leakages.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub should wait until the bathtub has been used at least when as this will settle it into its final position.
Preparing for the Installment
Firstly, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its final placement.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, causing the water to pass through the wall between the bathroom as well as the tiling, leading to difficulties with wetness as well as feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill the tub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our part on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Many thanks for finding the time to read our article. In case you enjoyed our blog entry kindly be sure to share it. Kudos for your time. Don't forget to pay a visit to our website back soon.
Book 24/7
Comments on “Exactly how to Replace a Bath Tub ( Guide).”